
P0340 means the powertrain control module (PCM) has detected a fault in the camshaft position sensor A circuit on Bank 1 (or the only camshaft sensor on single-sensor engines).
Key Takeaways
- Code P0340 indicates a missing or unusable signal from camshaft position sensor A, and it can cause long cranking, a no-start, or sudden stalling while driving.
- A failed sensor, chafed wiring, or a loose connector causes most P0340 codes.
- To fix P0340, replace the failed part, clear the code, and confirm the cam and crank signals stay in sync by restarting and taking a test drive.
What Does the P0340 Code Mean? Everything You Need to Know for a Quick Diagnosis
Code P0340 reads as Camshaft Position Sensor A Circuit (Bank 1 or Single Sensor). The PCM sets P0340 when it stops receiving a usable signal from camshaft position sensor A. On most engines, that is the intake cam sensor. Bank 1 is the side of the engine with cylinder 1, and inline engines have only one bank.
The camshaft position sensor tells the PCM where the camshaft sits in its rotation, so it knows which cylinder is on its compression stroke. The PCM pairs that signal with the crankshaft position sensor to control sequential fuel injection, spark, and variable valve timing.
The table below summarizes the problem and its solution for quick diagnosis.
| P0340 at a glance | Details |
|---|---|
| Definition | Camshaft Position Sensor A Circuit (Bank 1 or Single Sensor): The PCM isn’t receiving a valid signal from cam sensor A. |
| What it means | The PCM saw a missing or erratic cam signal while the crankshaft sensor showed the engine turning. |
| Most common cause | A failed camshaft position sensor, followed by chafed wiring or a loose, corroded connector. |
| First check | Back-probe the sensor connector for reference voltage and ground, since a dead circuit looks the same as a dead sensor. |
| Quick fix | Replace the part that failed testing, then clear the code and confirm it stays off through a restart and test drive. |
| Can you drive? | Not far. The engine can stall without warning or refuse to restart, so diagnose it before relying on the vehicle. |
P0340 Code Symptoms
The main symptoms of a P0340 code are a check engine light, long cranking or a no-start, and stalling. Without the cam signal, the PCM can’t confirm which cylinder is on its compression stroke. It delays or cuts fuel and spark until it finds another reference.
Long cranking that ends in a start is the most obvious sign. It shows the PCM falling back on the crankshaft sensor alone to work out engine timing.
The table below matches each symptom to what it usually means, in the order owners notice them.
| Symptom | What it usually means |
|---|---|
| Check engine light | The earliest sign. The PCM turns it on once it detects missing or erratic cam pulses, often on the first drive cycle with the fault. |
| Long cranking before the engine starts | The PCM falls back on the crankshaft sensor alone and needs extra revolutions to work out cylinder timing. |
| Engine cranks but won’t start | Some PCMs shut the fuel injectors off when the cam signal disappears, so the engine turns over without firing. |
| Stalling or misfires while driving | Intermittent signal dropouts upset injection and spark timing, so the engine stumbles or dies at idle and at stops. |
| Loss of power or limp-home mode | Many PCMs switch to a backup timing strategy and hold variable valve timing in its default position, so acceleration turns sluggish and fuel economy drops. |
| Related codes alongside P0340 | P0335 points to the crankshaft sensor circuit, P0341 to an erratic cam signal, and P0016 to a cam-crank correlation fault such as a stretched timing chain. |
Common Causes of P0340
A failed camshaft position sensor is the main culprit of P0340 codes, with wiring faults and low voltage right behind. First, check power, ground, and signal at the connector. A good sensor can’t send a signal through a broken circuit.
The table below matches each cause to how it sets P0340, starting with the most likely.
| Potential cause | How it sets P0340 |
|---|---|
| Faulty camshaft position sensor | Years of heat cycles break down the sensing element or its internal circuit. The sensor sends a weak, erratic, or missing signal. |
| Damaged wiring or corroded connectors | Heat-hardened insulation cracks and chafes against brackets, while oil from a leaking valve cover soaks the connector and adds resistance to the signal circuit. |
| Low battery or cranking voltage | A weak battery drops system voltage when the starter engages so the sensor can’t produce a clean signal during cranking. |
| Shorted 5-volt reference circuit | Many PCMs feed the cam sensor and other sensors, often the crankshaft sensor, from one shared reference. A short in any of them pulls the voltage down and cuts the cam signal. |
| Damaged reluctor wheel or wrong air gap | Chipped teeth on the cam reluctor, a sensor sitting out its bore, or a wrong-length replacement sensor weakens or distorts the pulses the PCM reads. |
| Jumped timing belt or stretched timing chain | The cam pulses arrive outside the window the PCM expects, though this fault more often sets P0016 on its own. |
| Failed powertrain control module | A rare internal fault in the signal input or reference supply misreads a good sensor. |
How Serious Is the P0340 Code?
P0340 is a high-severity code because the engine can stall without warning in heavy traffic or at highway speed. It can also leave the vehicle unable to restart after a stop.
Repeated misfires from an intermittent cam signal send unburned fuel into the exhaust, overheating the catalytic converter and potentially damaging it. That turns a sensor or wiring repair into a far more expensive job.
Diagnose P0340 as soon as it sets, and avoid long trips until you fix it.
How to Diagnose P0340
To diagnose P0340, confirm the sensor circuit has power, ground, and a switching signal before ordering parts. Use a scan tool, a digital multimeter, and a lab scope or graphing multimeter to isolate the fault. Follow these steps and stop at the first confirmed cause.
1. Scan for P0340 & related timing codes
Connect a scan tool to confirm P0340, then check for P0335, P0341, and P0016. P0335 stored with P0340 points to a shared power or reference fault, while P0016 points to a mechanical timing issue. Note the freeze frame data to see engine speed, battery voltage, and whether the code set during cranking or driving.
2. Inspect the sensor wiring & connector
Locate the camshaft position sensor on the cylinder head, timing cover, or valve cover. Unplug the connector. Then, check the pins for green corrosion, oil residue, or bent terminals, and trace the harness for chafing. Oil inside the connector usually means a leaking valve cover gasket or oil wicking through the sensor body. Fix both along with the sensor.
3. Test the sensor’s power, ground & signal
With the key on, back-probe the connector. A three-wire Hall-effect sensor should show 5 or 12 volts of reference, and the ground should drop less than 0.1 volts to battery negative. On a two-wire magnetic sensor, check resistance and AC output instead. Watch the signal wire on a lab scope while cranking. A flat line with good power and ground means the sensor failed.
4. Check the reluctor wheel & timing alignment
Remove the sensor and check its tip for damage, metal debris, or rub marks from the reluctor. Where the reluctor is visible through the sensor bore, turn the engine by hand. Use a flashlight to confirm the teeth are clean and intact. If the scan also shows P0016, verify the cam and crank timing marks before replacing any parts.
5. Check battery voltage & confirm the fault
Measure battery voltage at rest and during cranking. In most vehicles, a healthy battery reads about 12.6 volts at rest and should stay above 9.6 volts while cranking, or the sensor may not produce a clean signal. After any repair, clear the code, restart the engine several times, and test drive to confirm P0340 doesn’t return.
Manufacturer-Specific Causes & Solutions for P0340
P0340 means the same thing on every vehicle. But the sensor layout, setting conditions, and common failures may vary by brand. The following blocks cover common findings and the first check for five of the most-searched brands.
P0340 on Chevrolet
Chevy P0340 cases usually come down to the sensor itself or oil reaching its connector. A hardened sensor O-ring lets engine oil seep past the sensor body and into the plug, adding resistance to the signal circuit. Inspect the connector for oil before replacing the sensor. Fit a new O-ring with the replacement so the leak doesn’t return.
P0340 on Ford
A P0340 diagnosis on a Ford starts with confirming which cam sensor the PCM flagged. Similar to Chevrolet, a leaking sensor O-ring can let oil travel into the connector and harness. Inspect the plug for oil before ordering parts. If a new sensor and good wiring don’t clear the code, check the cam timing and the sensor’s target wheel.
P0340 on Toyota
Toyota notes that battery voltage below 11 volts can set P0340 or P0335. Test and charge the battery first. Save the freeze frame data before clearing the code. Replace the cam sensor only if the battery and the sensor circuit both check out.
P0340 on Nissan
Nissan’s 2.5L four-cylinder has a documented heat-related sensor failure. Nissan’s 2007 recall for 2002 and 2005–2006 Altima and Sentra models found the crankshaft sensor could overheat and lose its signal, stalling the engine.
Nissan’s fix was an ECU reprogram. Cam and crank sensor faults stall these engines the same way. Check for P0335 and open recalls alongside P0340. Then, test the cam sensor signal while the engine is hot.
P0340 on Dodge
Dodge, Chrysler, and Ram models with the 3.6L Pentastar V6 use two cam sensors, one on top of each valve cover at the transmission end. Each sensor reads both camshafts on its bank.
The PCM sets P0340 when it sees a crank signal but no cam signal for about 5 seconds of running. With the key on, check for 4.5 to 5 volts of reference and a good ground at the sensor before replacing it. The code takes three good trips to turn off the check engine light on its own.
How to Fix the P0340 Code
Fixing P0340 means repairing the part that failed testing, not replacing the sensor on reflex. Most repairs end at the sensor or its connector. But a new sensor on a shorted reference circuit or an oil-soaked plug may set the code again.
The table below matches each confirmed cause to its repair.
| Confirmed cause | Repair |
|---|---|
| Faulty camshaft position sensor | Replace a sensor that shows no signal with one with good power and ground. Lubricate the new O-ring with clean engine oil and torque the bolt to the manufacturer’s specification. |
| Damaged wiring or corroded connectors | Cut out damaged harness sections, solder in new wire, and seal each joint with heat-shrink tubing. Replace melted or corroded connectors with a new pigtail. |
| Oil-soaked connector | Fix the leak first, usually a valve cover gasket or sensor O-ring, then clean the connector with an electrical contact cleaner and let it dry before reconnecting. |
| Low battery or cranking voltage | Charge or replace a battery that drops below 9.6 volts while cranking, and clean the battery terminals so the PCM sees full voltage at startup. |
| Shorted 5-volt reference circuit | Unplug the sensors sharing the reference one at a time until the voltage returns, then repair the shorted sensor or wiring. |
| Damaged reluctor wheel or wrong air gap | Replace a damaged reluctor, reseat the sensor fully in its bore, and confirm the replacement sensor matches the original part. |
| Jumped timing belt or stretched timing chain | Replace the chain or belt with its guides and tensioners, then align the timing marks to factory specification. |
After any repair, clear the code and restart the engine several times, both cold and hot. Then test-drive through idle, stop-and-go traffic, and highway speeds while watching for new codes. A full drive cycle with no P0340 confirms the fix.
How to Prevent P0340 From Returning
To keep P0340 from returning, keep oil away from the sensor circuit, keep voltage steady at startup, and keep the timing components healthy.
- Change the oil at the recommended intervals
Clean oil limits wear on the timing chain, tensioner, and variable valve timing parts and helps prevent the timing faults that can set P0340 alongside P0016. - Fix oil leaks near the sensor promptly
Oil from a valve cover gasket or sensor O-ring can soak into the connector and break down wire insulation over time. - Inspect the sensor harness during routine service
Catching chafed or heat-hardened insulation early stops a short or open circuit before it sets the code. - Keep the battery healthy
Replace a battery that drops below 9.6 volts while cranking because low voltage can set P0340 on its own. - Use the correct replacement sensor
A sensor that matches the original part sits at the right air gap and reads the reluctor cleanly.
Stop P0340 From Coming Back With Identifix Direct-Hit®
A new sensor turns the light off, and the customer drives away. A week later, the P0340 is back. Every return visit costs your shop unbilled labor and a customer’s trust.
Identifix Direct-Hit® shows your technicians which repair actually kept P0340 from returning based on year, make, and model, using confirmed-fix data. OE wiring diagrams let your technicians trace the reference and ground circuits before ordering a sensor.
Contact us to see how Direct-Hit helps your shop fix P0340 on the first try.
FAQs
What is the most common cause of P0340?
A failed camshaft position sensor. Heat cycles break down the sensing element or its internal circuit until the signal weakens or stops. Wiring faults and low battery voltage are a close second. Test the circuit before you buy a sensor.
Can a bad crankshaft sensor, timing chain, or battery cause P0340?
Yes. A weak battery drops voltage during cranking, and a shorted crankshaft sensor can pull down the 5-volt reference it shares with the cam sensor. A stretched timing chain can also set P0340, though it more often sets P0016.
Can I drive with P0340, and can it damage the engine?
Only as far as the nearest repair shop. The engine can stall without warning in traffic or refuse to restart. Repeated misfires can also overheat and damage the catalytic converter.
How do I fix P0340 and how much does it cost?
Most repairs end with a new camshaft position sensor, which typically costs about $100 to $300 for parts and labor. Wiring repairs run about $50 to $150. If a stretched timing chain is the cause, replacement averages about $2,100 to $2,700.
Will P0340 clear itself, or can resetting the ECU fix it?
Not while the fault is still there. Resetting the ECU turns the light off, but the code returns as soon as the PCM sees the missing cam signal again. After a repair, the PCM will turn the light off on its own after about three consecutive good trips.

Identifix is the leading provider of automotive repair shop solutions and sevices designed to improve shop profitability and repair outcomes.

