
Key Takeaways
- P0302 means the engine control module detected a misfire in cylinder 2. It identifies the affected cylinder, not the failed component.
- Common symptoms include rough idling, engine vibration, hesitation, reduced power, poor fuel economy, and hard starting.
- A flashing check engine light indicates a misfire severe enough to risk catalytic-converter damage. Stop when safe rather than continuing to drive through the fault.
What Does the P0302 Code Mean? Everything You Need to Know for a Quick Diagnosis
The P0302 code reads “Cylinder 2 Misfire Detected,” meaning the engine control module (ECM or PCM) has detected that cylinder 2 isn’t producing its expected contribution to engine power.
- A weak or missing spark from a worn spark plug, failing ignition coil, damaged boot, or wiring fault can prevent cylinder 2 from igniting the mixture consistently.
- An incorrect air-fuel mixture caused by a restricted or leaking injector, low fuel pressure, or excessive fuel can disrupt combustion in cylinder 2.
- Insufficient compression from a burned valve, worn piston rings, damaged head gasket, or valve-train problem can prevent cylinder 2 from producing normal power.
The table below summarizes key aspects of the code and initial diagnostic checks.
| P0302 at a glance | Details |
| What it affects | The combustion event in cylinder 2 and, potentially, the engine’s emissions, power, and drivability. |
| What it means | The ECM detected a crankshaft-speed change consistent with cylinder 2 not producing normal power. |
| Most useful first check | Record all codes and freeze-frame data, confirm cylinder 2, and inspect or swap-test the ignition components. |
| Most common causes | A worn spark plug, weak ignition coil, injector fault, intake leak, wiring problem, or low compression. |
| Quick fix | Confirm whether the misfire follows the coil or plug before testing the injector, air supply, or mechanical condition. |
| Can you drive? | Avoid driving if the check engine light is flashing, the engine is shaking, or the vehicle has significant power loss. A steady light still requires prompt diagnosis. |
What Causes the P0302 Code?
P0302 can result from an ignition, fuel, air, electrical, or mechanical problem. Start with quick checks before moving to advanced testing if the misfire stays isolated to cylinder 2.
Faulty spark plug or ignition coil in cylinder 2
A worn, fouled, cracked, or incorrectly gapped spark plug can fail under cylinder pressure. A weak ignition coil, damaged boot, oil-filled plug well, loose terminal, or poor ground can produce the same code. Inspect the plug and coil, then swap-test the suspected component before replacing it.
Clogged or faulty fuel injector
A restricted injector may deliver too little fuel, while a leaking injector can create an over-rich mixture or foul the plug. An injector can also have a power, ground, control, or terminal problem. Use an approved injector balance test, current-ramp test, scan-tool test, or swap test to confirm the fault.
Vacuum leaks or intake manifold leaks
An intake-manifold gasket, injector seal, PCV hose, or vacuum line leak near cylinder 2 can create a cylinder-specific lean condition. Look for fuel-trim changes, a localized smoke-test leak, or an intake-runner problem rather than assuming the injector is restricted.
Low compression from damaged valves, piston rings, or head gasket
A burned valve, worn piston rings, damaged head gasket, broken valve spring, or valve-train fault can keep cylinder 2 from sealing. Low compression or excessive leak-down points toward a mechanical problem, but compare cylinder 2 with the other cylinders and follow the manufacturer’s test procedure before disassembly.
Wiring faults or engine timing problems
An open, short, poor terminal fit, or intermittent power or control circuit can interrupt the coil or injector. Incorrect camshaft timing, a stretched chain, or a damaged reluctor can also cause a misfire, especially when P0302 appears with correlation, camshaft, or crankshaft codes.
How Serious Is the P0302 Code?
P0302 should be diagnosed promptly. A steady check engine light with normal drivability may allow a short trip to the shop, but a flashing light, severe shaking, stalling, or major power loss means you should stop safely and limit further operation.
An active misfire can send unburned fuel into the exhaust, overheat the catalytic converter, and damage the substrate. Don’t keep driving with a flashing check engine light just because the vehicle still runs.
How to Diagnose the P0302 Code
Separate the diagnosis into ignition, fuel, air, and compression. Work from the easiest tests to the more invasive ones, and use the conditions in the freeze-frame data to reproduce the fault.
| Diagnostic step | What to check |
| Scan for Related OBD-II Codes and Freeze-Frame Data | Record all stored, pending, and history codes. Review engine speed, load, coolant temperature, fuel trims, and misfire counters. |
| Inspect and Test the Cylinder 2 Spark Plug and Ignition Coil | Confirm cylinder 2, then inspect the plug, boot, coil, connector, and wiring. Swap the coil with a known-good cylinder to see whether the misfire follows it. |
| Check Fuel Injector Operation and Electrical Connections | Test injector power, ground, control signal, terminal fit, and fuel delivery. Use an approved balance, current-ramp, scan-tool, or swap test. |
| Perform Compression and Leak-Down Tests | Compare cylinder 2 compression with the other cylinders. Use leak-down results to identify valve, piston-ring, head-gasket, or other mechanical leakage. |
| Inspect Intake Leaks and Engine Sensor Data | Smoke-test the cylinder 2 intake runner, manifold gasket, injector seal, PCV system, and vacuum hoses. Review fuel trims, air-fuel sensor data, throttle position, and engine load. |
How to Fix the P0302 Code
The repair depends on the test result. Replace only the component that the diagnosis identifies as faulty.
Replace a worn spark plug or faulty ignition coil
Replace a worn, damaged, or fouled plug with the specified part and gap. Replace the coil when a swap test or circuit test confirms that the misfire follows it, and correct any oil or coolant leak that caused contamination.
Clean or replace a defective fuel injector
Clean a serviceable injector only when testing shows a flow problem, and the manufacturer permits cleaning. Replace the injector when it is restricted, leaking, electrically faulty, or unable to meet the specified balance or flow result.
Repair vacuum leaks and damaged wiring
Replace leaking hoses, intake gaskets, injector seals, or PCV components. Repair damaged wires, loose terminals, poor grounds, or connector contamination, then verify power, ground, and control signals under the conditions that caused the misfire.
Address low compression or internal engine damage
Repair the valve, piston, head gasket, valve train, timing chain, or camshaft problem identified by the compression and leak-down results. Do not install an injector or ignition component as a substitute for an engine-mechanical repair.
Clear the code and confirm the misfire is resolved
Complete any required relearn procedure, clear the codes, and road-test the vehicle under the conditions that set P0302. Confirm that cylinder 2 misfire counts stay within the manufacturer’s limits and that no pending code returns.
How Much Does It Cost to Fix the P0302 Code?
P0302 repair cost depends on whether the fault is a simple ignition issue or an internal engine problem. Estimates vary by vehicle access, parts quality, labor rate, and the amount of diagnostic testing required.
| Repair path | Typical total range (USD) | What changes the cost |
| Diagnostic testing | 100-300 | Scan data, electrical testing, fuel testing, compression, and leak-down time. |
| Spark plug replacement | 1-00-400 | Plug access, whether the vehicle requires a complete set, and labor time. |
| Ignition coil replacement | 150-600 | Coil location, engine layout, and whether related plug or boot damage is present. |
| Injector diagnosis or replacement | 200-1,000+ | Injector access, programming, fuel-rail removal, and whether multiple injectors require service. |
| Vacuum or intake leak repair | 150-800 | Hose or gasket access, smoke-testing time, and intake manifold removal. |
| Compression or mechanical repair | 500-4,000+ | The cause of low compression, engine design, cylinder-head access, and required timing work. |
Note the vehicle year, engine, mileage, symptoms, and related codes before preparing an estimate.
P0302 vs. Other Misfire and Ignition Codes
The code number identifies the affected cylinder or system, but the diagnostic approach depends on the complete code set.
| Code | General meaning | Diagnostic distinction |
| P0300 | Random or multiple-cylinder misfire detected. | Look for a common cause, such as low fuel pressure, a vacuum leak, incorrect valve timing, or an air-fuel issue. |
| P0301 | Cylinder 1 misfire detected. | Follow the same ignition, fuel, air, and compression sequence for cylinder 1. |
| P0302 | Cylinder 2 misfire detected. | Focus first on cylinder 2, then check for system-wide causes if other cylinders also misfire. |
| P0303 or P0304 | Cylinder 3 or cylinder 4 misfire detected. | Confirm the cylinder location and compare the affected cylinder with known-good cylinders. |
| P0352 | Ignition coil B primary or secondary circuit fault. | Start with the coil circuit, power, ground, control signal, and wiring before diagnosing a mechanical misfire. |
P0302 Code by Car Make
The same cylinder-specific misfire code can require different tests depending on the engine design. Use the notes below as starting points, then follow the year- and engine-specific service information.
P0302 on Ford
On certain 2015–2018 Edge and 2017–2019 Escape and Fusion models with the 2.0-liter EcoBoost, P0302 accompanied by coolant loss, white exhaust smoke, or rough running warrants a coolant-intrusion investigation.
Ford’s bulletin describes cooling-system pressure testing and cylinder inspection before authorizing an engine repair. Check the engine and build-date applicability before treating the complaint as another failed coil.
P0302 on Toyota
For some 2018–2024 Camry, 2019–2024 RAV4, and 2021–2022 Avalon models with the A25A-FKS engine, the key clue is a misfire after a cold soak. Toyota bulletin T-SB-0010-24 covers misfire codes, including cylinder 2, recorded at coolant temperatures of 14°F–41°F.
If compression, ignition, and fuel-system checks pass, the procedure calls for replacing the exhaust-side hydraulic lash adjusters. Review the freeze-frame temperature before dismissing an intermittent cold-start complaint.
P0302 on Honda
A returning P0302 on certain 2017–2018 CR-V EX, EX-L, and Touring models calls for a look at the vehicle’s repair history. Honda bulletin 19-037 directs technicians to confirm whether earlier applicable bulletin repairs were completed, then inspect for fouled spark plugs if misfire codes return.
A separate whirling-noise complaint leads to camshaft inspection. The distinction matters: the bulletin does not prescribe valve adjustment or camshaft replacement for every cylinder 2 misfire.
P0302 on Nissan
For Nissan vehicles, keep the distinction between the detected misfire and its cause clear. Nissan P0302 diagnostic information reflects crankshaft-speed changes associated with cylinder 2; it does not establish that its ignition coil has failed.
Intake leaks and damaged connector terminals also warrant investigation. Use the engine-specific diagnostic procedure to narrow the fault rather than applying a single Altima, Rogue, or Sentra repair pattern across the range.
P0302 on Chevrolet
On some 2020–2021 Chevrolet Silverado 1500 applications with the 5.3L or 6.2L engine, GM bulletin 23-NA-043 links P0302 and other misfire codes to an internal lifter concern, including a collapsed or disassembled lifter. Confirm the exact engine and breakpoint before applying this pattern; standard ignition, fuel, and compression testing still comes first.
How to Prevent the P0302 Code
Preventing a cylinder-specific misfire starts with routine ignition maintenance and early attention to changes in engine performance.
Replace spark plugs at the recommended interval
Use the specified plug type and gap, and replace plugs at the manufacturer’s service interval. Inspect the removed plugs for oil, coolant, carbon, or signs of lean operation.
Keep ignition components and connectors clean
Check coil boots, connectors, grounds, and wiring for cracks, corrosion, oil, and water intrusion. Repair plug-well leaks before contamination damages the ignition system.
Address fuel and air problems early
Investigate hard starts, fuel-trim changes, vacuum leaks, injector noise, and fuel-pressure symptoms before they become a misfire. Don’t rely on fuel additives to fix a restricted injector or electrical fault.
Respond to warning lights promptly
A flashing check engine light indicates an active misfire that can damage the catalytic converter. Reduce the load, stop driving when safe, and diagnose the cause before returning the vehicle to service.
Diagnose P0302 Misfires With Direct-Hit
P0302 points to cylinder 2, but you need to test the affected system to identify the precise cause instead of replacing parts at random.
Identifix Direct-Hit combines confirmed fixes, OE service information, and interactive wiring diagrams in a search filtered by year, make, and model. Technicians can see which repairs resolved P0302 on the same vehicle and engine.
Book a demo to see how Direct-Hit can help your shop diagnose cylinder-specific misfires faster.
Frequently Asked Questions
Is it safe to drive with a P0302 code?
Avoid driving when the check engine light is flashing, the engine is shaking, or power is significantly reduced. A steady light may allow a short trip for diagnosis, but continued misfire can damage the catalytic converter.
Can a bad ignition coil cause P0302?
Yes. A weak or failing coil can prevent cylinder 2 from producing a consistent spark. Swap the coil with a known-good cylinder and rescan; a misfire that moves with the coil confirms the fault.
Can a fuel injector cause P0302?
Yes. A restricted, leaking, or electrically faulty cylinder 2 injector can cause lean, rich, or inconsistent combustion. Confirm injector operation with an approved balance, current, electrical, or swap test before replacing it.
Why does P0302 return after replacing the spark plug?
The plug may not have been the root cause, or the new plug may be contaminated by oil or fuel. If the misfire remains on cylinder 2, test the coil, injector, wiring, intake system, and compression.
Is cylinder 2 always the second cylinder in the firing order?
No. Cylinder numbering and physical location vary by engine, and cylinder 2 does not have to fire second. Confirm its location using the vehicle’s service information before testing components.
References
- A-Premium. (2026, May 13). Ignition coil or spark plug: How to tell what is causing your misfire. Retrieved October 23, 2026, from https://a-premium.com/blogs/ignition-coil-or-spark-plug[a-premium]
- Bosch. (n.d.). Gasoline direct injection systems. Bosch Mobility Aftermarket. Retrieved October 23, 2026, from https://www.boschaftermarket.com/xrm/media/images/country_specific/gb/services_2/downloads_1/xx_pdfs_17/gdi_repair_6p_folder2021_en_92073-1.pdf[boschaftermarket]
- Engine-Codes. (n.d.). P0302 Nissan code meaning, causes, symptoms & tech notes. Retrieved October 23, 2026, from https://www.engine-codes.com/p0302_nissan.html — Added.[engine-codes]
- Ford Motor Company. (2019, December 19). 2.0L EcoBoost—Coolant in cylinders, white exhaust smoke and/or illuminated MIL (Technical Service Bulletin 19-2346). National Highway Traffic Safety Administration. Retrieved October 23, 2026, from https://static.nhtsa.gov/odi/tsbs/2019/MC-10169807-0001.pdf — Added.[static.nhtsa]
- Ford Motor Company. (2022). 2.0L EcoBoost—Coolant in cylinders, white exhaust smoke and/or illuminated MIL. National Highway Traffic Safety Administration. Retrieved October 23, 2026, from https://static.nhtsa.gov/odi/tsbs/2022/MC-10214126-0001.pdf — Added.[static.nhtsa]
- American Honda Motor Co., Inc. (2024, April 12). Warranty extension: 2017–18 CR-V: DTC P0300, P0301, P0302, P0303, P0304, or P0172; whirling noise from engine (Service Bulletin 19-037, Version 5). National Highway Traffic Safety Administration. Retrieved October 23, 2026, from https://static.nhtsa.gov/odi/tsbs/2024/MC-10253309-0001.pdf — Added.[static.nhtsa]
- Identifix. (n.d.). Identifix auto repair software. Retrieved October 23, 2026, from https://www.identifix.com/[identifix]
- Identifix. (2026, October 20). P0352 code explained: Ignition coil B circuit issue. Retrieved October 23, 2026, from https://www.identifix.com/blogs/code-p0352-the-diagnostic-and-repair-guide/[identifix]

Identifix is the leading provider of automotive repair shop solutions and sevices designed to improve shop profitability and repair outcomes.

